







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Fairfield Owner’s Guide
We build Schluter-compatible home additions and ADUs in Fairfield, and a finished addition with Schluter waterproofing on the wet areas typically lands between $45,000 and $130,000 depending on size, foundation, and scope. A detached or attached ADU in Fairfield runs $90,000 to $220,000 and up, and a garage conversion between $30,000 and $80,000. Because this is planned construction, we schedule it like construction: a written scope, a start date, and a single inspection sequence.
Owners don’t usually call us because a Schluter part “failed.” They call because something beneath the finished tile let go. Water pools at the shower curb of a new bath addition. A grout joint along the floor drains the wrong direction. A slab-on-grade addition near the Suisun shore develops a soft, hollow-sounding strip by the exterior wall. That’s the tell. Schluter’s system parts (the drain flanges, the membranes, the edge profiles) are hidden once the job is closed up, and when they’re installed wrong or against an incompatible substrate, the symptom shows up months later at the surface.
Key Takeaways
- Schluter parts don’t wear out like a mechanical component. They fail when the substrate, the drain alignment, or the bonding is wrong.
- Fairfield’s shrink-swell clay soils and seasonal groundwater swing are hard on slab additions. Movement at the perimeter is the most common root cause we correct.
- Our technicians have up to 22 years of experience, and every addition carries the 365-Day Done Right Promise in writing.
- We’re an independent remodeling contractor. We are not affiliated with Schluter Systems.
Which Schluter Models This Applies To

If you’re trying to match a Schluter part to a model, the honest first answer is that most of the numbering you’ll see on a box is a nominal size callout, not a model year like a car. Schluter builds its systems around families of products, and knowing the family is what gets you the correct part. The three that matter most on an addition or ADU:
- KERDI-LINE and KERDI-DRAIN – linear and point drains for the shower or wet-bar areas of an addition. The grate width in millimeters (for example a 100 mm linear channel) has to match the rough-in, and the drain body must be bonded to a compatible substrate at the correct height before tile.
- DITRA and DITRA-HEAT – the uncoupling membrane under tile. The “150” and “250” designations refer to the tile size they’re rated for, not a generation. Using the wrong one over a wood-framed addition floor is a real failure path.
- SCHIENE, JOLLY, and RONDEC – the edge and trim profiles. The two numbers that identify a profile are the leg height and the material finish; the letter suffix tells you the outer edge shape.
Read the printed label: it gives the product family, the nominal dimension, and the material. Measure the actual opening or the tile edge with a caliper before you order. When it’s time to replace a profile or a drain grate, the OEM part guarantees the fitment; a quality aftermarket equivalent can work and often costs less, but only if the dimension and the material class match exactly. We don’t stock parts or carry them on a truck. We specify the correct part for your addition, source it, and install it as part of the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
Here are the symptoms we see on Fairfield additions, and what’s actually happening under each one.
- Cracked grout or popped tile along an exterior wall. This is differential movement between the addition slab and the original house. In Fairfield’s clay, that perimeter flexes more than a rigid bond can absorb, and an uncoupling membrane installed without proper perimeter isolation gives way first.
- Hollow or drummy tile near a shower or wet-bar drain. Almost always a bonding or height problem at the Schluter drain flange. The flange set too low leaves a thin-set void that reads as a hollow tap and lets water track under the membrane.
- Water staining or efflorescence on the lower tile or grout. Water is getting behind the system, not through it. The KERDI band at a seam, corner, or curb was skipped or installed with the wrong overlap and the shower is wicking moisture into the framed wall.
- A profile or edge trim that’s lifting or loose. The SCHIENE or JOLLY leg wasn’t fully embedded in the thin-set at the tile edge. Once it’s loose, it can’t be re-bedded without pulling the adjacent tile.
- A soft, spongy feel under a wood-framed addition floor. The substrate (the structural floor beneath the membrane) is deflecting more than the membrane can decouple. This is a framing problem first and a tile problem second, and patching the surface won’t fix it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Fairfield, a home addition with properly specified Schluter waterproofing runs $45,000 to $130,000; an ADU is $90,000 to $220,000; a garage conversion is $30,000 to $80,000. A localized repair (a drain flange reset, a membrane seam corrected, an edge profile replaced) is priced inside those ranges as a line item, not a mystery number, and we give you the written price before work starts.
What drives the range: the size and foundation of the addition, whether the wet area is a full bath or a simple wet bar (a full bathroom remodel within the addition is $9,000 to $28,000 on its own), slab versus crawlspace, and how much of the existing structure has to be opened up to reach the failed substrate. We break parts and labor out on the quote so you can see what the Schluter system parts and the membrane and drain work actually cost versus the framing and finish.
Every addition we complete is covered by the 365-Day Done Right Promise. For a full year after close, if the work fails, we return and correct it at no charge. The written guarantee is in your hand at the end, along with a clean site and documented scope.
DIY or Call Us?
Some things you can safely check yourself. Tap along the tile and mark where it sounds hollow. Look at the grout lines near the exterior wall and the drain for cracks or hairlines. Shine a light at a seam in the shower and see if the membrane edge is visible or pulling. Those are observational and cost nothing.
Where DIY goes wrong is the repair. Re-setting a Schluter drain flange or re-bonding a membrane means removing tile, getting down to the substrate, and rebuilding the waterproofing to the correct height and overlap. Getting the height off by a few millimeters, or bonding to a substrate that’s still moving, brings the same failure back within a season. That’s the part we do, and it’s the part the guarantee covers.
If you suspect the problem is structural movement under the addition floor, don’t open it up to take a look. Call us, and we’ll tell you what we’re seeing on the phone. A real person answers at (833) 998-3242, seven days a week.
FAQs

A properly installed Schluter system (membrane, drain, and profiles) is designed to outlast the tile on top of it, often decades. The realistic failure window in Fairfield is the first one to three years, because that’s when slab movement from our shrink-swell clay and seasonal groundwater shows up. If it’s going to fail on install error, it fails early.
Sometimes it can be repaired. A single edge profile, a drain grate, or a localized membrane seam can often be corrected without a full tear-out. A drummy floor that runs wall to wall usually means the substrate is moving and the fix is bigger. We tell you which one you’re looking at after we see it, and the written price comes before any work.
A localized repair (profile replacement, drain reset, seam correction) is usually a one- to three-day job once the part is in hand. A full addition or ADU is a scheduled build measured in weeks, not days, and we give you the date range in the written scope. We don’t promise same-day on planned construction.
We read the label or the spec on the existing installation, confirm the product family and the dimension, and order the part against your addition’s actual measurements. We don’t stock parts, so there’s no guessing at what’s on a shelf. We specify it, source it, and install it as part of the job. If you also want premium finish materials, we work with a documented roster that includes KraftMaid, Cambria, and Silestone alongside Schluter.
If a Fairfield addition is showing tile cracks, a hollow floor, or water where it shouldn’t be, the sooner we look, the smaller the repair. Bradford Remodeling Co Fairfield puts the price in writing before work starts, answers the phone with a live person, and stands behind every completed addition for a full year under the 365-Day Done Right Promise. Call (833) 998-3242 for a free estimate on your Fairfield home addition or ADU.
Written by the team at Bradford Remodeling Co Fairfield, serving Fairfield and nearby areas.












